Vertical Sync sensor

Buttonbox (2018)

2018 Buttonbox
Downloads
Buttonbox 2018 RuSocSci (Python package)

The Vertical Sync sensor is used on a computer/laptop monitor for time accurate visual presentation. The sensor measures screen brightness. It generates a BITSI trigger("A" = ON/light, "a" = OFF/noLight) when the amount of light is higher than the (customizable) threshold, which means that the exact onset of any visual stimulus can be marked. It can easily be attached to any screen with a pincher. The Vertical Sync sensor is connected to a computer with a usb connection.

BITSI Protocol

BITSI stands for Bits to Serial Interface. Because the BITSI is designed to interface both in- and output signals, the 'protocol' is asymmetric: the input and output protocols differ.

Vertical Sync sensor
ASCII (rise/fall)	Code (rise/fall)	Light
A / a	65 / 97	ON / OFF

This means that when signal 1 gets active(button press), a capital A will be sent to the serial port. A lowercase 'a' will be sent when the signal is deactivated(button release). Mechanical buttons can be connected directly.

Output

Output knows two protocols: BITSI simple or BITSI extended. To enter a certain protocol two buttons have to be pressed when the BITSIbox is powered or com port opens. [2015]Press button H and A for simple mode and H and B for extended mode. [2018]Press button E and A for simple mode and E and B for extended mode.

If no button is pressed when powered it boots the last known protocol. In the simple protocol every byte sent to the BITSI over the serial port, is represented at the 8 bit output.

The extended protocol uses two bytes(or two characters), this combination can access two analog outputs and a tone generator. The first byte selects the output. The second byte determines the value written to this output.

BITSI Extended
Function	Byte 1 (ASCII/code)	Byte 2
Marker Out	M / 77	Marker Value
Pulse Out	P / 80	Marker Value
Pulse Time	X / 88	ms before pulse reset
Analog Out 1	Y / 89	Analog Output Value
Analog Out 2	Z / 90	Analog Output Value
Tone	T / 84	Start Tone
Detect Sound	D /	S / 83
Detect Voice	D /	V / 83
Calibrate Sound	C /	S
Calibrate Voice	C /	V
Analog In 1	A /	1
Analog In 2	A /	2
Analog In 3	A /	3
Analog In 4	A /	4
LEDs Off	L /	X
LEDs Input	L /	I
LEDs Output	L /	O

Port Settings

Trigger port

Schematic view of the 25 pins connector

The 25 pins female connector has 8 inputs and 8 outputs, respectively 1-8 are inputs and 9-16 are outputs. Three analog input with an analog to digital convertor of 12 bit, pins 17,18,20 and 21. Two analog outputs with an digital to analog convertor of 12 bits on pins 22 and 23.

The inputs 1-8 will be pulled down from 5V to GND when the buttons are pressed. The outputs 9-16 will be pulled up from GND to 5V when the output is activated.

Serial port

Our hardware design allows to be connected to the computers USB and emulates a serial communication Port.

Baudrate	115200
Parity	None
Data bits	8
Stop bits	1
Flow control	None

USB-Com port

1.Connect the BITSIbox to your computer using the USB cable.

2.When you connect the BITSIbox, Windows should initiate the driver installation process (if you haven't used the computer with an BITSIbox board before).

3.On Windows Vista/7, the driver should be automatically downloaded and installed.

4.On Windows XP, the Add New Hardware wizard will open:

• When asked Can Windows connect to Windows Update to search for software? select No, not this time. Click next.
• Select Install from a list or specified location (Advanced) and click next.
• Make sure that Search for the best driver in these locations is checked; uncheck Search removable media; check Include this location in the search and browse to the c:/beheer/arduino/drivers directory.
• The wizard will search for the driver and then tell you that a "USB Serial Converter" was found. Click finish.
• The new hardware wizard will appear again. Go through the same steps and select the same options and location to search. This time, a "USB Serial Port" will be found.

How to Check the Com Port settings(important!)

• From the Start menu, open the Control Panel.

• From the control panel, open the System window.

• From the system properties window, go to the Hardware tab and click the Device Manager button.

• From the Device Manager window, click Ports (Com&LPT). You should now be able to see which Com Port the USB adapter is assigned to.

• If the Com Port is 10 or higher, you will have to change it to a lower port.

• From the Device Manager window, click on USB Serial Port (Com#). Click the Port Settings tab of the USB Serial Port Properties window, and then click the Advanced button.

• In the Advanced Settings window, use the scroll input to select a Com Port (select 10 or lower). Change Receive (bytes) and Transmit (bytes) to 64. Change the Latency Timer to 1.

• Click the OK button.

Always connect the usb device to the same port and your settings will be remembered.

Software Settings

Neurobs Presentation

The experiment files needs a few settings for the device to work:

• In the settings tab: port -> input port -> 1 must be the device that identifies itself as "Arduino Uno" in the device manager. Note that the port must have a number not higher than 10 (COM1-COM10). Use re-enumerate if it is higher.
• Rate must be set 115200, Parity to None, Data Bits to 8 and Stop Bits to 1, Uncheck FIFO Interrupt.

Testing Buttonbox

When pressing on the A button within the input channel tester. You will see the following ASCII code.

Adding Marker

Testing Markers (output)

Send code 1 for Button A

Button A will light up.

Send code 0 for clearing.

Example PCL code you can program a handle to send a marker:

#handle:
output_port OutputPort = output_port_manager.get_port( 1 );

Example to send a marker:

OutputPort.send_code(100); #create a marker

for more information see chapter 8 in the presentation course by clicking here

Python/PsychoPy

Download this site-package to use the buttonbox: rusocsci

or use in windows command 'pip install --upgrade rusocsci'

Example using buttons from the buttonbox in Python:

 1#!/usr/bin/env python
 2
 3# import the rusocsci.buttonbox module
 4from rusocsci import buttonbox 
 5
 6# make a buttonbox
 7bb = buttonbox.Buttonbox()
 8
 9# wait for a single button press
10b = bb.waitButtons()
11
12# print the button pressed
13print("b: {}".format(b))

Example using markers with the buttonbox in Python:

 1#!/usr/bin/env python
 2
 3# import the rusocsci.buttonbox module
 4from rusocsci import buttonbox 
 5
 6# make a buttonbox
 7bb = buttonbox.Buttonbox()
 8
 9# send a marker
10bb.sendMarker(val=100)    #This is your marker code, range code 1-255

Example using BITSI extended in Python:

 1#!/usr/bin/env python
 2
 3# import the rusocsci.buttonbox module
 4from rusocsci import buttonbox 
 5
 6# make a buttonbox
 7bb = buttonbox.Buttonbox()
 8
 9# select a function
10bb.sendMarker(val=(ord(X)))    #select pulse time
11bb.sendMarker(val=2)           #set time of dureation pulse to 2ms
12
13bb.sendMarker(val=(ord(M)))    #select marker out
14bb.sendMarker(val=115)           #set marker value 115

Example using BITSI extended analog read in Python:

 1#!/usr/bin/env python
 2
 3# import the rusocsci.buttonbox module
 4import serial
 5
 6# make a buttonbox
 7ser = serial.Serial("COM2", 115200, timeout = 0.10 )
 8ser = serial.Serial("/dev/ttyUSB0", 115200, timeout = 0.10 )
 9
10while True:
11	ser.write('A1')
12	ser.flush()
13	x = ser.readline()
14	visual.TextStim(win, text=x).draw()
15
16	# black screen for 1000 ms
17	win.flip()
18
19	key = event.getKeys()
20	try:
21		if key[0]=='escape':
22			break
23	except:
24		continue

Example using the Buttonbox in PsychoPy:

 1#!/usr/bin/env python
 2
 3# import psychopy and rusocsci
 4from psychopy import core, visual 
 5from rusocsci import buttonbox
 6
 7## Setup Section
 8win = visual.Window(monitor="testMonitor")
 9bb = buttonbox.Buttonbox()
10text = visual.TextStim(win, "Press a button on the buttonbox")
11
12## Experiment Section
13# show text
14text.draw()
15win.flip()
16# wait for response
17b = bb.waitButtons()
18# show response
19text.setText("you pressed: {}".format(b))
20text.draw()
21win.flip()
22core.wait(5)
23
24## Cleanup Section
25core.quit()

For more documentation click here: http://pythonhosted.org//RuSocSci/index.html

Matlab

Example using markers with the Buttonbox in Matlab:

Download the file Bitsi.m from the DCCN website: https://intranet.donders.ru.nl/index.php?id=bitsim0
Make sure to have this file in your Matlab path.

1% At the start of your script, create the buttonbox serial object
2bb = Bitsi("COM2");
3% other code
4        :

BITSI simple mode:

 1% This example is for an EEG system sampling at 500Hz samplerate.  
 2% at the start of your script, reset marker
 3samplerate = 500;
 4pulseLen = 2000/samplerate;
 5bb.sendTrigger(0);
 6% send a marker
 7val = 1;                                     % val: this is your marker code, range code 1-255
 8bb.sendTrigger(val);
 9java.lang.Thread.sleep(pulseLen);    % wait long enough for the EEG system to capture the trigger, i.e., 2000/samplerate ms
10% reset marker
11bb.sendTrigger(0)                 % Note: if resetting the marker is not possible at this moment in code, you can decide to do this later as long as it has taken place long enough before the next marker has to be sent.

BITSI extended mode:

1samplerate = 500;
2pulseLen = 2000/samplerate;
3% select a function
4bb.sendTrigger(uint8('X'));   % select pulse time
5bb.sendTrigger(pulseLen);             % set time of duration pulse to (2000/samplerate) ms
6 
7val = 1;                                     % val: this is your marker code, range code 1-255
8bb.sendTrigger(uint8('M'));  % select marker out
9bb.sendTrigger(val);              % val: this is your marker code, range code 1-255

1% At the end of your script, close the buttonbox serial object
2    :
3bb.close();