Difference between revisions of "BalanceBoard Lab"

From TSG Doc
Jump to navigation Jump to search
(Redirected page to Balance Board)
 
(10 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
= Balance board =
+
#REDIRECT [[Balance Board]]
−
{|
 
−
|-
 
−
| [[File:eyelink.jpg|200px|Image: 200 pixels]]
 
−
|}
 
−
 
 
−
== Introduction ==
 
−
 
 
−
A balance board(force platform) is commonly used in motor control labs and neurologic clinics. They essentially consist of a set of finely calibrated scales, measuring mechanical forces. The pattern of forces can be used to derive body position, at a high spatial and temporal resolution.
 
−
 
 
−
== Description ==
 
−
 
 
−
There are several boards specified up to 1M2 and 0,5M2 with a sub-millimeter spatial resolution and a 200 hz temporal resolution.
 
−
 
 
−
A typical balance board records at a high spatial and temporal resolution. Regarding spatial resolution: a platform can detect changes from a few sub-millimeters (freezing) to at least 500 centimeter (forward or backward steps). The platform records reliably over four vertical forces. Regarding temporal resolution: the signals are typically sampled at 200 Hz. Even though the system allows even higher sampling rates, in practice 100 Hz is sufficient.
 
−
 
 
−
The pressure sensors derive directly from the wii balance board. Each sensor has a maximum pressure of 120Kg. In-house electronics is build to get a clean amplification from the sensors. A National instruments card, USB-6221, takes care of the A/D conversion and connects with usb to a pc. The force plate can be integrated into existing systems for stimulus presentation and for recording bodily signals such as EEG, EMG and heart rate. In practice, this means that the systems are time-locked within millisecond accuracy.
 
−
 
 
−
== Instructions ==
 
−
 
 
−
Find the BalanceboardCalibration manual here [[Media:SOP_1_BalanceboardCalibration.pdf]]
 
−
 
 
−
Find the BalanceBoardBaseline manual here [[Media:SOP_2_BalanceBoardBaseline.pdf]]
 
−
 
 
−
Find the InstructionPosture manual here [[Media:SOP_3_InstructionPosture.pdf]]
 
−
 
 
−
== Technical design ==
 
−
{|
 
−
|-
 
−
| [[File:Capture.JPG|200px|Image: 200 pixels]]
 
−
|}
 
−
 
 
−
== National instruments settings ==
 
−
{|
 
−
|-
 
−
| [[File:eyelink.jpg|200px|Image: 200 pixels]]
 
−
|}
 
−
 
 
−
== Presentation software ==
 
−
 
 
−
<nowiki>
 
−
sub runtrials_national begin
 
−
 
 
−
# The dio_device will setup NI-DAQmx device number 1 "Dev1"
 
−
dio_device card = new dio_device(ni_dio_device, 1, 0 );
 
−
#int id = card.acquire_analog_input( "MyVoltageOutTask" );
 
−
int id1 = card.acquire_analog_input( "ForceMeasurement,Voltage_0" );
 
−
int id2 = card.acquire_analog_input( "ForceMeasurement,Voltage_1" );
 
−
int id3 = card.acquire_analog_input( "ForceMeasurement,Voltage_2" );
 
−
int id4 = card.acquire_analog_input( "ForceMeasurement,Voltage_3" );
 
−
count_old = response_manager.total_response_count();
 
−
loop
 
−
until false
 
−
begin
 
−
if response_manager.total_response_count() > count_old then
 
−
count_old = response_manager.total_response_count();
 
−
calibrate_board = true;
 
−
end;
 
−
 
−
message_scale[1] = round(round(card.read_analog( id1, 1000.0 ),6) * 1000.0, 0);
 
−
message_scale[2] = round(round(card.read_analog( id2, 1000.0 ),6) * 1000.0, 0);
 
−
message_scale[3] = round(round(card.read_analog( id3, 1000.0 ),6) * 1000.0, 0);
 
−
message_scale[4] = round(round(card.read_analog( id4, 1000.0 ),6) * 1000.0, 0);
 
−
 
−
if calibrate_board then
 
−
zero_scale_left_up    = message_scale[left_up];
 
−
zero_scale_left_down  = message_scale[left_down];
 
−
zero_scale_right_up  = message_scale[right_up];
 
−
zero_scale_right_down = message_scale[right_down];
 
−
calibrate_board = false;
 
−
end;
 
−
 
−
message_scale[left_up]    = message_scale[left_up] - zero_scale_left_up;
 
−
message_scale[left_down]  = message_scale[left_down] - zero_scale_left_down;
 
−
message_scale[right_up]  = message_scale[right_up] - zero_scale_right_up;
 
−
message_scale[right_down] = message_scale[right_down] - zero_scale_right_down;
 
−
t_scale11.set_caption(string(message_scale[left_up]));
 
−
t_scale11.redraw();
 
−
t_scale22.set_caption(string(message_scale[left_down]));
 
−
t_scale22.redraw();
 
−
t_scale33.set_caption(string(message_scale[right_up]));
 
−
t_scale33.redraw();
 
−
t_scale44.set_caption(string(message_scale[right_down]));
 
−
t_scale44.redraw();
 
−
 
−
pos_dot_x = (message_scale[right_up] + message_scale[right_down]) - message_scale[left_up] + message_scale[left_down]);
 
−
pos_dot_y = (message_scale[left_up] + message_scale[right_up]) - message_scale[left_down] + message_scale[right_down]);
 
−
p_balance.add_part( balance_pos, (pos_dot_x * 1.0), (pos_dot_y * 1.0));
 
−
t_coord.set_caption(string(pos_dot_x)+","+string(pos_dot_y));
 
−
t_coord.redraw();
 
−
 
−
p_balance.present();
 
−
p_balance.remove_part( 8 );
 
−
end;
 
−
card.release_analog_input( id1 );
 
−
card.release_analog_input( id2 );
 
−
card.release_analog_input( id3 );
 
−
card.release_analog_input( id4 );
 
−
end;
 
−
</nowiki>
 
−
 
 
−
== Python software ==
 
−
 
 
−
<nowiki>
 
−
from PyDAQmx import Task
 
−
from PyDAQmx.DAQmxConstants import *
 
−
from PyDAQmx.DAQmxTypes import *
 
−
import numpy
 
−
import msvcrt
 
−
import time
 
−
 
 
−
times = []
 
−
try :
 
−
    freq = 100.0 # Hz
 
−
    numinputs = 4
 
−
 
 
−
    analog_input = Task()
 
−
    read = int32()
 
−
    timer= time.clock()
 
−
    running = True
 
−
 
 
−
    data = numpy.zeros((numinputs,), dtype=numpy.float64)
 
−
 
 
−
    #DAQmx Configure Code
 
−
    analog_input.CreateAIVoltageChan("Dev1/ai0:%i" % (numinputs - 1), None, DAQmx_Val_RSE, -10.0,10.0,DAQmx_Val_Volts,None)
 
−
    #analog_input.CfgInputBuffer(0)
 
−
    #analog_input.CfgSampClkTiming("",freq,DAQmx_Val_Rising,DAQmx_Val_ContSamps,1000)
 
−
 
 
−
    analog_input.StartTask()
 
−
    datalist = []
 
−
    while running:
 
−
        #DAQmx Start Code
 
−
       
 
−
   
 
−
       
 
−
        timeBeforeRead = time.clock()
 
−
        analog_input.ReadAnalogF64(-1,10.0,DAQmx_Val_GroupByChannel,data,numinputs*2,byref(read),None)
 
−
        ser.write('S')
 
−
        line = ser.readline()
 
−
 
 
−
        time.sleep((1 / freq) - (time.clock()- timeBeforeRead))
 
−
       
 
−
        times.append(timeBeforeRead - time.clock())
 
−
     
 
−
 
 
−
        if msvcrt.kbhit():
 
−
            running = False
 
−
       
 
−
 
 
−
finally :
 
−
    print "Stop"
 
−
    t = numpy.array(times)
 
−
    afwijking = numpy.mean(abs(t - numpy.mean(t)))
 
−
    maxafwijking = max(abs(t-numpy.mean(t)))
 
−
   
 
−
    print numpy.mean(t), afwijking, maxafwijking
 
−
 
 
−
 
 
−
    analog_input.StopTask();
 
−
</nowiki>
 

Latest revision as of 09:45, 10 August 2015

Redirect to:

Retrieved from "http://tsgdoc.socsci.ru.nl/index.php?title=BalanceBoard_Lab&oldid=3128"